Comments

You must log in or register to comment.

_genepool_ t1_ix7n1v6 wrote

No good way to tell. Try going in the same hole on an angle to miss the rebar.

3

[deleted] t1_ix7of0s wrote

I worked with drilling into concrete ceilings for a living. Put the anchor diagonally in any direction from the current dud hole compared to the rooms angles.

Sounds complicated - but isn’t. Most rooms are square or rectangular. Just go from your hole towards a corner in the room by about 10 cm and try there instead. Most anchors are fine to be at a slight angle, and whatever you hang in them should be adjustable by a tiny amount anyway.

If It isn’t, just move the whole mount anchor by that same amount in the best suited random corner of the room direction.

3

stay_or_go_69 OP t1_ix7y77j wrote

Thanks this is very interesting advice. I'm actually putting in climbing anchors, so they need to hold a lot of weight.

I ordered a device for detecting studs and cables from amazon. Hopefully that will also be useful.

2

[deleted] t1_ix82909 wrote

Ooh climbing anchors sound fun. That’s got to be quite deep to hold any good weight in concrete. I only worked with static weight anchors - once finished there will be no change in weight or pressure at any given anchor.

To have concrete holes drilled that could hold a lot of weight shifting over and over seems like It mostly Depends on the anchor, since regular screws rarely hold anything over 5 kg reliably, and not when you jerk It around.

If you don’t mind, keep me updated! I’m intrigued.

1

Khalkeus_ t1_ix85wjm wrote

The reason for this is that the rebar is most likely a grid of 20cm squares placed along the walls of the room. If the ceiling is poured concrete. If, on the other hand, it is made from prefab elements, all rebar will probably run in one direction only.

1

Aearly1 t1_ix7w1us wrote

They do make bits called rebar eaters. If you find a hole with rebar you can switch bits and turn the roto hammer on drill mode, it will cut right through.

2

mick_ward t1_ix7ncr1 wrote

Stanley makes a magnetic stud finder for about $5 (model 47-400). It's basically a magnet on a pivot. It might work for you. However, if there's a lot of rebar, it could be more confusing than helpful.

1

prean625 t1_ix85397 wrote

Rebar is meant to have 50mm approx cover of concrete. Sounds like you found dodgy construction if youre hitting it at 10mm. Slowly drilling into steel with a titanium drill head should get through it however

1

jakkarth t1_ix86bus wrote

Your submission has been removed for one or more of the following reason(s):

  • Your question does not include the research you've done to find an answer yourself, or why that research didn't answer your question.

This is a basic requirement so others do not spend time repeating your steps. It is not a judgement about your question being "too easy." We're looking for evidence that you've made an attempt yourself.

  • Please do not use /r/DIY as your first stop for questions - we are not Google.

  • Please search Google and /r/DIY to see if your question has been asked before. Check owners manuals, tech support forums or contact the manufacturer.

  • Have you already done some basic research and are still stuck?

  • Please include what research you have done in your question so that others do not repeat your steps.

  • Consider posting your question in the sticky thread at the top of the subreddit.

  • Ask your question in our Discord server in the appropriate channel.

Please read our Full Sub Rules before resubmitting.

If you believe this was a mistake, please message the moderators.

###Do not respond to this comment - you will not receive a response.

1

mlansang t1_ix7mlaq wrote

Studfinder with setting for metal stud?

0

outofipswich t1_ix7ncwl wrote

Rebar is just steel. Why not swap to a standard drill of the same size and continue in the same hole?

0